Not how to solve the electronic loadometer
HENGQUASI:2017-03-02 16:29:27

Not how to solve the electronic loadometer

电子秤不准了,需要重点检查以下部位,北京衡准专业销售电子秤维修服务一条龙服务010-61732587

Electronic scale is not allowed, the need to focus on the following parts, Beijing quasi professional sales of electronic scale maintenance service one-stop service 010-61732587

1、地磅每个角数值不一样原因：传感器损坏，秤体不平整、接线盒决绝方案：查看秤体周围、底部是否有障碍物堵塞。查看传感器是否有悬空、松动，所以传感器最好受力点一致，秤主要的就是;衡。查看所以线路是否连接正常，接线盒是否进水、受潮或脱线。然后进行每个角的调试。

1, loadometer each corner values are not the same due to sensor damage, the scale body is not smooth, the junction box scheme: see refuse scale body bottom around whether there are obstacles blocking. Check whether there is suspended, sensor loose, so the best sensor point, scale is the major scale. View so that the line is connected properly, water, whether damp or off-line junction box. Then debug each corner.

2、称量不准现象：称量误差较大。 原因：秤台与基础有问题，仪表调校不准确，仪表模拟部分坏，传感器、接线盒有问题、四角有误差等。显示正超载或负超载 现象：如XK3190系列仪表显示【Err03】正超载或显示【Err02】负超载。 原因：仪表损坏，供桥电源不正常，传感器、接线盒、DB-9插头等有问题引起信号大幅度变化，若是一台未经调试的秤，调试后故障自动消除，或是地磅传感器有问题。

2, the phenomenon of weighing is not allowed: the larger the weighing error. Reason: the scale table and the foundation has the question, the gauge adjustment is not accurate, the instrument simulation part is bad, the sensor, the junction box has the question, four angles has the error and so on. Show positive or negative overload phenomenon: such as XK3190 series meter [Err03] is overloaded or display [Err02] negative overload. Reason: instrument damage, bridge power supply is not normal, sensor, junction box, DB-9 plug and other problems caused by signal changes, if a table without debugging scales, after debugging automatic fault elimination, or loadometer sensor problem.

3、开机无自检 现象：仪表接通电源后无任何显示或显示部分笔划段，有的还伴有蜂鸣器鸣叫。 原因：外部220V电源及供电电路(线路、保险管、机内变压器、三端稳压电源)有故障，仪表PCB板损坏或LED显示管损坏或连线脱落。

3, no self boot phenomenon: no display or display strokes of the instrument connected to power, sometimes accompanied by buzzer. Cause: external 220V power supply and power supply circuit (line, safety, internal transformer, three terminal power supply) failure, instrument PCB board damage or LED display tube damage or line off.

4、开机或卸载后不回零 现象：开机接通电源，仪表自检后显示不为零，有错误提示或显示一较稳定的数值，或在称量中车辆下秤后显示正或负的数值，不显示零位。 原因：仪表放大部分有故障，传感器性能改变(滞后，漂移等)，秤体与基础间有杂物堵塞。

4, boot or not after unloading to zero phenomenon: switch on the power supply is switched on, after the display instrument self-test is not zero, the error or display a numerical stable, or in the vehicle weighing scale showed a positive or negative value is not zero. Cause: the instrument amplifier is faulty, the performance of the sensor is changed (lag, drift, etc.), and there is debris blockage between the scale and the foundation.

北京衡准专业销售电子秤,电子地磅,北京地区电子秤维修服务热线:13521224539

Beijing HengZhun sales professional electronic scales, electronic loadometer, Beijing electronic scale maintenance service hotline: 13521224539